An environment filled with dust is very uncomfortable. It is also quite common sense that an environment packed with dust leads to several health hazards. Whether it’s an industrial-size woodworking factory, or a home garage shop, a cyclone dust collector is the best way to deal with the dust produced by cutting and sanding. In some cases in point, a cyclone dust collector is not a choice but an utter necessity.
A shop vac is adequate for a small quantity of dust, but to have the ultimate dust-free and hygienic air in your shop, a powerful cyclone dust collector is the best solution. And when it comes to cyclone dust collectors, Jet is considered one of the best in the business.
So in this Jet cyclone dust collector review, we will help you choose from three of the most efficient cyclone dust collector models provided by Jet.
A Comparative Overview
Let’s have a look at the comparative chart below before going into the detailed review.
With Jet cyclone dust collector you can experience the power of proficiency. Features of this machine will give you a new environment experience in your shop. Let’s talk about those features in this jet cyclone dust collector 1.5hp review.
It has a steel tube frame to support its 143 lb weighed body. The body is made of 18 gauge steel, which makes it very strong. It comes with a dimension of 43.8 x 23.2 x 33.5 inches.
With its powerful 1.5 hp motor, the cyclone’s two-stage separation provides more CFM air velocity than a single-stage unit. Its two-stage separation uplifts the fine particulates and pulls heavy debris into the collection drum. The drum unit has independent caster and quick-release levers for easy and quick discard. This provides continuous suction and better productivity for the same horsepower.
Dust Collecting Capacity
The upper canister filtration system is directly mounted to the cyclone dust collector without accessory hoses. Its upper filter is pleated. The fine dust particulates are filtered through pleated material which can capture particulates down to 1 micron.
The jet cyclone dust collector is also equipped with a radio frequency remote control. It works from a distance of up to 50 feet.
Swivel caster makes it easy to shift the unit around. It gives the unit total portability in the shop or on a job site.
- The smallest of dust particles get captured by the pleated material
- The heavy-debris 20-gallon tank is easy to empty
- Filters are directly mounted
- Remote controlled
- Relatively expensive
Q: How much noise does this unit make?
A: The sound emission of this unit is 75 dB at 3m.
Q: Can this be used as a stationary unit using a 4″ pipe and blast gates at all tools?
This is another efficient dust collector model from Jet. This is the perfect choice for you if you have a medium-sized shop. Let’s start the Jet JCDC-2 2 hp cyclone dust collector review and learn more about the features of this unit.
Its 193 lb body is supported by a steel tube frame. This unit’s dimension is 47.5 x 27.2 x 41 inches. Its strong body is also made of 18 gauge steel. It’s a bit heavier than other collectors of its class as it packs a bigger filter, dust drum, and motor which increases the efficiency of its work.
It comes with a powerful 2 hp motor. The cyclone’s two-stage separation offers more CFM air velocity than comparable horsepower single-stage units. With its two-stage separation, heavy debris gets dragged down to collection drum and fine dust particles get filtered through pleated material. A 30-gallon drum captures the heavy debris, which has quick-release levers and independent caster for speedy discarding. And the pleated filter gets cleaned by a double paddle manual cleaning system.
Dust Collecting Capacity
Directly mounted filters exclude inefficiencies from bends and ridged flex hosing. This excellent filtration system allows a constant flow of air. Fine dust particles get filtered through the pleated material and it even captures particles down to 1 micron and below.
This Jet JCDC-2 2 HP Cyclone Dust Collector is also equipped with radio frequency remote control. It works from a distance of up to 50 feet. Remote timer setting allows the system to continue running for 2, 4, 6, or 8 hours before automatic shutoff.
It’s easy to shift the unit around the shop with its swivel casters. This dust collector is conveniently portable.
- Easy to empty the drum
- High-quality design
- High-quality filters
- Easy to useable
- Excellent portability
- Captures the smallest particles
- A bit difficult to assemble
Q: Is it possible to put a bag in the 30-gallon drum?
Q: Does this unit have a manual crank to clean the filter?
A: Yes, on top. And it’s very easy-going.
The Jet JCDC-3 is by far one of the best cyclone dust collectors available out there in the market. It combines high performance and sufficient power in one well-designed and high-quality package that you can get to improve the quality of the air in your shop. Let’s have a closer look.
Its body weighs 242 lb. and the frame is made of steel tubes. This high-quality unit also comes with a relatively stronger 18 gauge steel body. The collection drum capacity of this unit is 66-gallon which is far more than the other Jet cyclone dust collector models.
With its 3 hp motor, it can put out as much as 1240 CFM suction power and this will assist you to maintain the quality of air in your shop to the healthiest level. Its two-stage separation allows fine dust particles to get filtered through pleated materials and heavy debris to get pulled down to the collection drum. It has a big 66-gallon drum that captures the heavy debris and it also has independent casters and quick-release levers for quick emptying. A double paddle manual cleaning system swiftly cleans the pleated filter.
Dust Collecting Capacity
It’s an excellent dust collector with a direct mounted filter for high efficiency. Its pleated filter even captures the smallest particles down to 1 micron and less.
It has a radio frequency remote control that works from the distance of up to 50 feet. The remote timer setting system can be allowed to run for 2, 4, 6, or 8 hours before it shuts off automatically.
Swivel casters make it convenient for the passage around the shop.
- High suction power
- Longer-lasting and more durable than the other two
- Low usage of power
- Can handle up to 3 tools at a time
- Automatic shutoff
- A slight loose battery compartment
Q: What is the overall assembled height of the unit?
A: It’s about 7 feet.
Q: Do the suction ports handle 4″ flex hose?
A: Yes, they do. Up to three at a time.
From Jet 1-1/2hp cyclone dust collector review it is understandable that this unit is not that bad with its cheaper price tag than the others. And with its ability to generate enough suction power the Jet JCDC-2 was not far behind from the best. But With all the research and the gathered information, the most impressive among these three is the Jet JCDC-3. It is very efficient and does an amazing job while collecting dust and keeping the air healthy. It can handle up to 3 tools with ease and bear the extended ducting for a continuous air purification performance. So go ahead, make the pick that suits you best.
More Dust Collector & Cyclone:
- The Top 6 Best Cyclone Dust Collector
- Jet Cyclone Dust Collector Reviews [JCDC-1.5 1.5, JCDC-2 2 hp & JCDC-3 3 hp]
- Grizzly Dust Collector – Master for woodworking projects
- Grizzly Cyclone Dust Collector – Solve the Dust creates problems
- Is Woodworker Need the Powermatic Dust Collector?
Sup? This is John Boson signing in from my very own Garage and Woodworking station here! I hate to introduce myself as an expert, rather I am more of a person who loves to share the knowledge for people’s interest. Ping me at firstname.lastname@example.org to let me know if my job on this website has helped you or not. Also, you can request for my honest review or a piece on any know-how topic for what I will try my best. Cheers! Signing out!